Where You Can Find It!

Find it at RJay's!

LOKAR PERFORMANCE PRODUCTS

BILLET SPECIALTIES

Flaming River

PETE & JAKE'S HOT ROD PARTS

SUPER BELL AXLES

DIRECT SHEETMETAL


RJAYS DOT COM - THE PLACE TO SHOP!

1928-32 Ford Cross Steer Rack & Pinion

Features:
Direct replacement for Vega style steering box, mounts on the same brackets as the Vega.
Retro fit kit includes everything needed to replace Vega Steering.
No welding or drilling required, installs in less than an hour.
Rack and pinion has a smooth consistent effort through its entire travel, unlike Vega Boxes.
Rack kit is polished and plated to compliment existing chromed components.
Automotive grade rack shaft and pinion will accommodate vehicles exceeding 3000 pounds.
Increase ground and engine clearance.
Vega Box click to enlarge
Cross Steer
A Rack & Pinion on a straight axle? Yes, it is now possible with Cross Steer®, a rack & pinion unit designed specifically for 1928-1934 Ford street rods. This innovative design steers off one side, creating very little bump steer that would occur using a traditional rack & pinion. There is no play in the rack travel, and is smooth and consistent throughout the length of its travel. This means that Cross Steer® eliminates tight spots and loose spots so common with conventional steering boxes.
The Cross Steer® Rack & Pinion offers a significant reduction in steering effort, even at low speeds. Cross Steer® has 6 full inches of rack travel at the rate of about 1.6 per rotation of the pinion, giving Cross Steer® about 3.75 turns lock to lock as compared to a typical Vega style steering box with 4 turns lock to lock.
Installation is easy! It takes about an hour to install when replacing a Vega style steering box. Cross Steer® utilizes a bracket that mounts to the existing Vega style bracket on your frame.
Cross Steer® is available in a New Build Kit and Retro-Fit Kit, the difference being the Retro Kit is for users replacing a Vega style steering box, it includes a coupler, section of shaft, and hardware. This compensates for the distance between the Cross Steer® pinion and the Vega spline, so you can use this shaft and hook up your column with out modification, using even the same U-Joint!
The New Build Kit doesn't include the extension shaft kit. If you are building a new car you can run a U-joint directly to the 9/16"-26 splined pinion on the Cross Steer®.
Cross Steer® also comes with a lifetime warranty and satisfaction guaranteed!
RACK SPECS:
Turns Lock to Lock: 3.75 Travel: 6" Thread: 11/16"-18 LH Spline: 9/16"-26
CLICK HERE TO LOOK AT PRODUCT INSTRUCTIONS

click to enlarge 1928-32 Ford Cross Steer®
New Build Kit / Black Bracket Fits Vega Mount
Tie Rod End is Not Included (Order Below)
Pinion Shaft is 9/16"-26 Spline
Part No. Description / Application RJay's Buy It!
MAV8000460-01 New Build Kit - Use this kit for a new installation, not replacing an existing Vega steering box. $374.99


click to enlarge 1928-32 Ford Cross Steer®
New Build Kit / CHROME Bracket Fits Vega Mount
Tie Rod End is Not Included (Order Below)
Pinion Shaft is 9/16"-26 Spline
Part No. Description / Application RJay's Buy It!
MAV8000460-02 New Build Kit - Use this kit for a new installation, not replacing an existing Vega box. Chrome Bracket. $499.99


click to enlarge 1928-32 Ford Cross Steer®
Includes Rack & Pinion with Bracket Only
Pinion Shaft is 9/16"-26 Spline
Part No. Description / Application RJay's Buy It!
MAV8000500 1928-32 Cross Steer with bracket only. Does not include drag link tube or shaft extension kit. $359.99


click to enlarge 1928-32 Ford Cross Steer®
Retro-Fit Kit / Replaces Existing Vega Box
Extension Shaft Kit is Inlcuded
Tie Rod End is Not Included (Order Below)
Pinion Shaft is 9/16"-26 Spline
Part No. Description / Application RJay's Buy It!
MAV8000470-01 Retro-Fit Kit - Use this kit for replacing an existing Vega steering box. Includes extension shaft kit. $419.99


click to enlarge

Chrome Tie Rod End
Fits the Cross Steers Listed Above

Part No. Description / Application RJay's Buy It!
MAV8021480 Chrome Tie Rod End - 11/16"-18 LH Thread $34.99


click to enlarge

Plain Tie Rod End
Fits the Cross Steers Listed Above

Part No. Description / Application RJay's Buy It!
MAV8021480 Plain Tie Rod End - 11/16"-18 LH Thread $27.99


click to enlarge

Vega Box Retro-Fit shaft Kit
Same Shaft Kit as with #MAV8000470-01 Cross Steer Kit

The kit consists of a pinch bolt style coupler to fit the 9/16"-26 Spline of the Cross Steer® Rack & Pinion, a long section of shaft with one end 5/8"-36 Spline, the same size of the original Vega style steering box. Also included are a drill bit and two roll pins to attach the shaft to the coupler once it is cut to the necessary length. The shaft and coupler come in a nickel plated finish.
Part No. Description / Application RJay's Buy It!
MAV8050020 Vega Retro-Fit Extension Shaft Kit $44.99


click to enlarge 1928-32 Ford Cross Steer®
NEW Right Hand Steer!
Tie Rod End is Not Included (Order Below)
Pinion Shaft is 9/16"-26 Spline
Part No. Description / Application RJay's Buy It!
MAV8000650-01 New Right Hand Steer Rack for those who drive on the "wrong side" of the road! $374.99


clikc to enlarge



RJay's Speed Shop, LLC
434 East 3rd St. / Adrian, MO 64720
Contact RJay's Speed Shop
Phones: e-mail:
Toll Free: 1-800-258-4204 Tech/Parts Questions
Phone: 1-816-291-4575 Order Inquiries
Fax: 1-816-841-4721 General Mailbox
All Materials Copyright © Flying A Motorsports, Inc.
Reproduction of any material prohibited without written permission.

top