 |
| Note: Headers are non-returnable unless they are absolutely new in the original packaging with un-opened hardware. Any scratches or other damage renders them as "used" making them impossible to sell to another customer. |
 |
CC1 Designed to fit 1927 and up automobiles with small block Chevy engines. This header will fit any rack and pinion setup. Also fits Vega steering and any Mustang-style mounted steering that is mounted with 2" clearance from the steering gear to the center ports on the driver's side. The header will clear any motor mounts, tie rods, or steering rods. Any starter combination will clear this header except cast iron Powerglides. This is the most compact true performance header available. Comes with all hardware necessary for installation. |
 |
|
| Part No. | Description / Application | RJay's Price | Buy It! |
| CC1 | SBC Blockhugger Headers - Plain Steel Finish | $175.00 | |
| CC1-C | SBC Blockhugger Headers - Ceramic Silver Coated | $315.00 |
|
CC1-5/8 Our best selling small block header design now fits even tighter to the block! The new specifications below provide even better steering and chassis clearance. Features 1-5/8" tubing and a 3" collector for all but the most radical street motors. Include all hardware required for installation. |
|
|
| Part No. | Description / Application | RJay's Price | Buy It! |
| CC1-5/8 | SBC Blockhugger Headers - Plain Steel Finish | $225.00 | |
| CC1-5/8-C | SBC Blockhugger Headers - Ceramic Silver Coated | $375.00 |
 |
CC1-3/4 A big tube header, for small block Chevy recommended for blown and high RPM motors. Similar in design to the CC1, this header is not available in stainless steel. Available for angle plugs -- specify which heads you are using. Comes with all hardware necessary for installation. |
|
|
| Part No. | Description / Application | RJay's Price | Buy It! |
| CC1-3/4 | SBC Blockhugger Headers - Plain Steel Finish | $285.00 | |
| CC1-3/4-C | SBC Blockhugger Headers - Ceramic Silver Coated | $435.00 |
 |
CC1-7/8 Specially designed header plate for 1-7/8" tubes. No adaptor required. This header is a good choice for blown and high RPM motors. Similar in appearance to CC1-3/4 -- right and left sides are the same. Available for angle plugs -- specify which heads you are using. Comes with all hardware necessary for installation. |
|
|
| Part No. | Description / Application | RJay's Price | Buy It! |
| CC1-7/8 | SBC Blockhugger Headers - Plain Steel Finish | $315.00 | |
| CC1-7/8-C | SBC Blockhugger Headers - Ceramic Silver Coated | $465.00 |
 |
CC1AP Designed for use with angle plug heads. It is a very tight fitting header using 1 5/8" tubing with a 3" collector. A high performance street header, works well in 1927-up automobiles with small block Chevrolet engines. Comes with all hardware necessary for installation. (Ceramic Coating shown in picture) |
|
|
| Part No. | Description / Application | RJay's Price | Buy It! |
| CC1AP | SBC Blockhugger Headers - Plain Steel Finish | $225.00 | |
| CC1AP-C | SBC Blockhugger Headers - Ceramic Silver Coated | $375.00 |
 |
CC1HO This header was designed for the new General Motors High Output engine with angle plugs and D-Port heads. Comes with all hardware necessary for installation. |
|
|
| Part No. | Description / Application | RJay's Price | Buy It! |
| CC1HO | SBC Blockhugger Headers - Plain Steel Finish | $225.00 | |
| CC1HO-C | SBC Blockhugger Headers - Ceramic Silver Coated | $375.00 |
|
CC1K Originally developed for Kugel pinch nose frame, the CC1K fits any application where steering, frame rail, or side panel interferes with first primary tube. Distance from the head to the outside of the first tube is only 1-1/2". Comes with all hardware necessary for installation. |
|
 |
*Distance
from the head to the outside of the first tube is 1-1/2". |
|
|
|
| Part No. | Description / Application | RJay's Price | Buy It! |
| CC1K | SBC Blockhugger Headers - Plain Steel Finish | $225.00 | |
| CC1K-C | SBC Blockhugger Headers - Ceramic Silver Coated | $375.00 |
 |
CC1T This is a tighter fitting CC1, designed for use on small block Chevrolet engines. For cars with a pinched nose frame, Model T's and A's, full fendered with a hood. Comes with all hardware necessary for installation. |
|
|
| Part No. | Description / Application | RJay's Price | Buy It! |
| CC1T | SBC Blockhugger Headers - Plain Steel Finish | $225.00 | |
| CC1T-C | SBC Blockhugger Headers - Ceramic Silver Coated | $375.00 |
|
CC1LS1 New design for LS1 heads places the collector slightly off-center. Fits tight to block and measures only 7-3/4" from center of flange to the bottom of the collector. Standard in 1-1/2" tubing with 2-1/2" collector. 1-5/8" or 1-3/4" tubing with 3" collector available - Call RJay. (Ceramic Coating shown in picture) |
|
|
| Part No. | Description / Application | RJay's Price | Buy It! |
| CC1LS1 | SBC Blockhugger Headers - Plain Steel Finish | $315.00 | |
| CC1LS1-C | SBC Blockhugger Headers - Ceramic Silver Coated | $465.00 |
 |
CC2 This 4" tall header speaks for iself. One header fits both sides of your small block Chevy engine. This header has excellent clearance for both straight and angle plug heads. Fits all Dart, Trick Flow, Brodix, Brownfield, Edelbrock, and Chevy angle plug hands. When ordering, be sure to specify exactly which head manufacturer and model you are running. Comes with all hardware necessary for installation. |
|
|
| Part No. | Description / Application | RJay's Price | Buy It! |
| CC2 | SBC Blockhugger Headers - Plain Steel Finish | $225.00 | |
| CC2-C | SBC Blockhugger Headers - Ceramic Silver Coated | $375.00 |
 |
CC3 The CC3 header has right and left sides. Left side angles back 15°, right side angles back 5°. This header works great with Camaro type subframes with cross members and steering box interference. Good choice for '55-up Chevy pickups, but may require modification for A/C or alternator brackets, and/or motor mounts depending on year of truck, engine and tranny type, and accesssories. Comes with all hardware necessary for installation. |
|
|
| Part No. | Description / Application | RJay's Price | Buy It! |
| CC3 | SBC Blockhugger Headers - Plain Steel Finish | $225.00 | |
| CC3-C | SBC Blockhugger Headers - Ceramic Silver Coated | $375.00 |
 |
CC4 A small block Chevy header for use in 1935-40 Fords using standard and Saginaw power steering. Must use off-set side motor mount on the driver's side. No reducers are necessary. Comes with all hardware necessary for installation. |
|
|
| Part No. | Description / Application | RJay's Price | Buy It! |
| CC4 | SBC Blockhugger Headers - Plain Steel Finish | $225.00 | |
| CC4-C | SBC Blockhugger Headers - Ceramic Silver Coated | $375.00 |
 |
||||||||||
7079
Hwy ZZ / Cuba, MO 65453
All Materials Copyright © 1999-2006 RJay's Performance Center, LLC Reproduction of any material prohibited without written permission. Contact website owner: RJay's Webmaster |
| |
| top |